Fillable Printable Tmde Calibration And Repair Data

Tmde Calibration And Repair Data

1. JOB ORDER NUMBER 2. PRIORITY 3. IDENTIFICATION CODE

4. TECHNICAL BULLETIN 5. TECHNICAL MANUAL 6. SCHEDULE UIC 7. OWNER UIC

8. SERIAL NUMBER 9. MODEL NUMBER 10. MFG CODE

11. NATIONAL STOCK NUMBER 12. DUE DATE 13. INT 14. SYSTEM CODE 15. NOMENCLATURE

16. WORK CENTER TEAM 17. LEVEL 18. ACTION DATE 19. PERFORMING UIC

21. EQUIP READINESS CODE 23. REPORT CODE

24. CHANGE DATA

25. DEFICIENCIES/SYMPTOMS

31. PARTS ADJUSTED

32. PARTS REPLACED

33. REMARKS

35b. DATE

36b. DATE

37b. DATE

35a. SUBMITTED BY

36a. RECEIVED UNDER LIMITED TECHNICAL INSPECTION BY

37a. ACCEPTED

TMDE CALIBRATION AND REPAIR DATA

For use of this form see 750-25; the proponent agency is USAMC

30. CALIBRATION

20. TYPE STANDARD MW ELEC

PHYS IR RAD

22. UPDATE

ADD CHANGE DELETE

26. STATUS

a. PUIC b. CODE c. DATE d. INIT

27. CALIBRATION

CONDITION

a. WITHIN TOLERANCE

b. OUT OF TOLERANCE

28. REPAIR/ADJUSTMENT

a. BY TEAM/LAB

b. DEFERRED MAINT

c. NRTS/CODE OUT

29. REPAIR

TECH CODE HOURS TECH CODE HOURS

34. ARTS REQUISITIONED

a. REF DESIG

b. NOMENCLATURE c. MFG CODE

d. NATIONAL STOCK NO./

PART NO.

QTY

f. UNIT

ISSUE

g. UNIT

COST

h. DOCUMENT

NUMBER

i. RECEIVED

DA FORM 7372, DEC 1996

AMXTM 34A, 1 Dec 87, and AMSMI 34A, 1 Apr 96, are obsolete.

APD LC v1.00

WHEN COMPLETING THIS FORM, SEE TB 750-25.

BLOCK 8 - SERIAL NUMBER. Must have entry. Do not precede with zeros. If longer than ten

digits, delete from left side. Must use joint electronics type designator system (JETDS) serial

number. Manufacturer's serial number will be used for non-JETDS items. Do not include

special characters, e.g., "/", "-", or "@", etc.

BLOCK 9 - MODEL NUMBER. Must have entry. JETDS numbers must be used if applicable.

Manufacturer's model number is used if non-JETDS item.

BLOCK 10 - MFG CODE. Must have entry. See TB 43-180 or SB 708-43 and SB 708-48.

Entry will be five zeros if JETDS item, or where no MFG CODE is known.

BLOCK 13 - INTERVAL CODES. Reference TB 43-180

720

1080

USAPSL Special Only

960

Training

CNR

CBU (Admin storage)

BLOCK 23 - REPORT CODES

CODE

DEFINITION

Audit or Inspection

Computer/Peripheral Repair

Deployment

Limited/Special Calibration

Normal Actions

Programming Effort

Special Project

Wipe Test

Reliability Check

BLOCK 22 - GENERAL CUSTOMER INSTRUCTIONS

FOR ADD, CHANGE, OR DELETE.

Reference TB 750-25 when completing this block.

BLOCK 26 - STATUS/DISPOSITION CODES

CODE DEFINITION

Received (To Repair)

Received (To Calibrate)

Awaiting Manual/TB/TM

Awaiting Additional Equipment/Accessories

Awaiting Standard/Accessories

Awaiting Repair Parts

Awaiting Shop (Repair Diagnosis)

Awaiting Shop (Repair 100%)

Awaiting Shop (Calibration)

In-Shop (On the Bench)

Awaiting Customer Pick-up

Awaiting Transportation

Awaiting Shipment

Evacuation to Another Team/Lab

Evacuated to Factory

Returned to Customer's DS

Returned to Customer

Placed in Float/RX Stock

Salvaged/Coded

120

150

180

210

240

270

300

330

360

450

One time only

540

630

480

600

390

420

510

570

660

690

840

MANHOUR CONVERSION CHART

FOR BLOCKS 29 AND 30.

MINUTES

1-6

7-12

13-18

19-24

25-30

31-36

37-42

43-48

49-54

55-60

HOUR

TENTHS OF

BLOCK 21 - EQUIPMENT READINESS CODE (ERC).

Reference AR 220-1, Appendices B and C.

CODE

DEFINITION

Principal Weapon System/Equipment

Auxiliary Equipment (AE)

Administrative Support Equipment (ASE)

Pacing Item

CODE INTERVAL/DAYS CODE INTERVAL/DAYS

DA FORM 7372, DEC 1996

Page 2 of 2

APD LC v1.00